SEARCH

Getting Started
1g DSM Datalogging
OBDII Datalogging
Rtek7 ECU Upgrade
PDA Information

PocketLOGGER DSM
PocketLOGGER OBDII
PocketLOGGER ZT
KnockBOX
Rtek7 ECU Upgrade
Jeep Window Block
Hotsync Cables
PL Log Viewer

PocketLOGGER DSM
PocketLOGGER OBDII
KnockBOX
Rtek7 ECU Upgrade
PDA Information
Forum
Ordering/Shipping
Warranty/Returns
Help Ticket
About Us
Contact Us
IMPORTANT
DTI Is Closed
As of Dec 2017, DTI is no longer selling products.
The site remains up for support purposes.

Rtek7 S5 TII Stage 1



Rtek7 Home >> S5 TII Stage 1ORDER AT RIGHT

Feature Details:

Below are expanded descriptions of features that are included with the S5 TII Stage 1 Rtek7 ECU Upgrade.

FCD:

The stock ECU will cut fuel to the rear rotor when boost hits the fuel cut threshold of about 8.6 psi. Although this was put into the stock ECU as a protection mechanism, it's a quite harsh mechanism and not required for mild improvements in boost.

Up until now, a Fuel Cut Defensers (FCDs) have been external devices wired into the engine harness that interrupt the signal from the boost sensor to the ECU. The Rtek7 goes goes right to the source by removing the code responsible for Fuel Cut from the ECU altogether. This has the additional benefits in that it doesn't alter the boost signal to the in-dash gauge, there are no wires to splice, and no additional box to clutter the engine bay.

CAUTION: Running too much boost without enough fuel can destroy an engine. Even though the FCD is built into the ECU, it is the customer's responsibility to address fuel requirements separately.

MOP Removal:

On the S5 series, the oil injection pump (MOP) is electronic and controlled by the ECU. If the ECU detects a failure of the MOP it will enter limp mode. This makes removal of the pump impossible with the stock ECU. The MOP Removal feature defeats the operation of the pump and detection of pump failures (codes 20, 26, 27 and 37), thus allowing complete removal of the pump. Premix or the more reliable S4 mechanical pump can then be used.

CAUTION: This mod should not be used if you intend to continue operation of the electronic MOP.

AWS:

When you first start your RX7, the ECU will rev the engine to approximately 3000 RPM's - this is the Accelerated Warmup System (AWS) in action. The purpose of the AWS is to warm up the precat. Of course, one of the worst things you can do to a cold engine is high revs. This mod removes the AWS code from the ECU allowing your car to idle normally when cold.

Minimum Injector Size:

This is the size of the injectors that the ECU is expecting.

The injectors MUST be the same size or larger than the minimum injector size for the chip version you have or engine damage will result.

550cc secondaries are stock so no change has been made to the fuel map in version 1.5. For version 1.7, the fuel map has been corrected to compensate for larger 720cc secondary injectors without the need for external fuel control, like an AFC, to keep from running very rich. If you have an AFC, it will no longer have to trick the ECU to compensate for the larger injectors. The AFC can be used for fine tuning. This also means that you CANNOT run version 1.7 in a car with 550cc secondaries or you will run lean. Likewise, version 1.8 is expecting at least 720cc injectors for both the primary and secondaries. Injectors with any less flow will run lean and can lead to engine damage. It is OK to run larger that the minimum injector size, but be aware that you will need some sort of fuel control to keep them from running very rich, or move to an Rtek7 Stage 2 ECU upgrade.

Lower secondary staging rpm:

Normally the secondary injectors start adding fuel at 3800 RPM. The problem is that the secondary injectors will not come on below this rpm regardless of the boost being run. This can lead to cars running lean below 3800rpm even if they have larger injectors, fuel pump etc. Lowering the RPM at which the secondary injectors come on allows them to add fuel before the primary injectors start to max out.

Timing retard above 9psi:

The stock ECU has no additional timing control for above around 9-10psi. This mod extends the timing control to give a little more safety for those running 9+ psi. Timing is pulled about one degree per PSI.

 
Order: or Find a Dealer

Rtek7 ECU Upgrade
Stage 1.5
$120 / $140
(Self / DTI Install)

Stage 1.7
$130 / $150
(Self / DTI Install)

Stage 1.8
$130 / $150
(Self / DTI Install)

Upgrade from v1.x
to 1.7 or 1.8
$15* / $30
(Self / DTI Install)



* 1.x chip must be sent back before upgrade chip is shipped.
Customer review:
Rtek7 ECU Upgrade:
I really like the product a lot, especially those who are looking for a better and more cost effective way to get rid ... more
-Jesse Watts, Nashville, TN
Other Products:


Sitemap  |  Press Room  |  Legal Information  |  Privacy Information

© 2001-2010 digital tuning, inc. All rights reserved.